Some links on this page are affiliate links: if you buy through them we may earn a commission, at no extra cost to you.
To restart and set a Glashütte Original Seventies, first identify the exact reference, then release the screw-down crown while the watch is dry. In the general Glashütte Original three-position layout, the crown’s first operating position winds the movement, the first pull-out position corrects the date, and the second pull-out position sets the time while stopping the seconds hand. Push the crown home and screw it down fully before the watch goes near water.
Seventies models using Calibre 37-02 are self-winding chronographs with a stated power reserve of 70 hours ±5%. That means a fully wound example is specified to run for roughly 66.5 to 73.5 hours, although the exact adjustment procedure for the date, crown direction and chronograph controls depends on the reference. The instructions below separate what is common across the family from what must be checked in the manual for your watch.
As an Amazon Associate I earn from qualifying purchases.
Which Glashütte Original Seventies reference do I have?
Read the reference engraved on the case back before changing anything. The Seventies family includes standard and limited editions with different dial layouts, straps and chronograph details. Glashütte Original’s service system uses the reference number to return the applicable functions and technical information, so the number is more reliable than a nickname such as “Seventies Chronograph.”
| Reference | Movement and winding | Case and water specification | Running time | Documented functions |
|---|---|---|---|---|
| 1-37-02-08-02-70 | Automatic Calibre 37-02; screw-down crown | 10 bar water resistance; dimensions not stated on the cited page | 70 hours ±5% | Hour and minute display, stop-second chronograph, small seconds, 30-minute and 12-hour counters, Panorama Date, power-reserve display and flyback |
| 1-37-02-20-02-70 | Automatic Calibre 37-02; screw-down crown | 40 × 40 mm stainless-steel case; 10 bar water resistance | Up to 70 hours | Hour and minute display, stop-second chronograph, small seconds, 30-minute and 12-hour counters, Panorama Date, power-reserve display and flyback |
| 1-37-02-21-02-70 | Automatic Calibre 37-02; screw-down crown | 40 × 40 mm case; 10 bar water resistance | 70 hours ±5% | Hour and minute display, stop-second chronograph, small seconds, 30-minute and 12-hour counters, Panorama Date, power-reserve display and flyback |
The 40.00 × 40.00 mm dimensions, 10-bar rating and 70-hour reserve are figures stated by Glashütte Original on the cited product pages; those pages do not show a publication year. Stainless-steel bracelet versions cited for the family list a 26 mm end-link width, but that measurement does not by itself confirm compatibility with every Seventies reference.
Popular on Amazon
- Premium Carbon Fiber Leather Construction - Crafted from carbon fiber leather, durable MDF, and clear acrylic glass, this single watch winder offers lasting protection with a refined, modern look. It keeps your automatic watch securely displayed while adding a premium touch to your bedroom, office, or dresser.
- Quiet and Anti-Magnetic Japanese Motor - Equipped with a Japanese ultra-quiet motor, this watch winder operates smoothly with low noise for a more comfortable day and night experience. The anti-magnetic design helps protect your watch movement from magnetic interference and supports accurate performance over time.
- Dual Power Supply with Adjustable Pillow - Power this automatic watch winder with a USB-C cable or 2 AA batteries not included for flexible use at home or while traveling. The adjustable pillow is designed to fit a wide range of watch sizes, making it suitable for both men’s and women’s watches.
- Preset Rotation Cycle for Balanced Winding - This watch winder operates in a preset cycle of clockwise rotation for 2 minutes, rest for 6 minutes, counterclockwise rotation for 2 minutes, and rest for 6 minutes. This balanced rotation pattern helps keep your automatic watch wound while avoiding unnecessary continuous movement. For best results, manually wind the crown 20 to 40 turns before placing your watch in the winder to help prevent stoppage.
- Stylish Gift for Watch Lovers - With its modern design and practical function, this single watch winder makes a thoughtful gift for watch lovers, collectors, husbands, fathers, and friends. It is a great choice for birthdays, anniversaries, Father’s Day, Christmas, and other special occasions.
What should I check before operating the crown?
Work on a dry watch with clean hands and identify the reference first. A screw-down crown is both a control and part of the case seal, so forcing it can damage the threads or compromise water resistance.
- Place the watch on a stable, soft surface so the case and crystal are not scratched.
- Make sure the crown and case are dry. Do not unscrew, wind or set the watch in water.
- Look for the reference on the case back and use that number in the Glashütte Original service information system or the watch’s supplied manual.
- If the crown feels gritty, cross-threaded, unusually tight or impossible to release, stop. Do not use pliers, tools or force.
- If the watch has been dropped, exposed to moisture or shows condensation under the crystal, leave the crown untouched and contact an authorised Glashütte Original service partner.
How do I wind a stopped Seventies automatic watch?
Release the screw-down crown, use the winding position and turn it in the direction specified for your reference. The watch will also wind from normal wrist movement, but manual winding is the simplest way to restart one that has run down.
Free tools Windows power users keep installed
One-click scans. No signup required.
- Release the crown. With the watch dry, turn the crown counterclockwise until the screw thread disengages and the crown springs free to operate. If it does not release smoothly, stop rather than forcing it.
- Leave the crown in the winding position. In the general Glashütte Original layout, this is position 1: the crown remains pushed in after the screw-down threads have been released.
- Turn the crown to build reserve. Turn it in the winding direction stated in the manual for the exact reference. The public Seventies product pages identify the movement as automatic but do not state a reference-specific crown direction, so do not rely on a guessed direction. A few turns are normally used to restart a stopped automatic in general mechanical-watch guidance, but Glashütte Original does not publish a fixed Seventies turn count in the cited material.
- Check that the seconds hand has started. Once the balance is running, you can wear the watch or continue winding as required. The automatic rotor replenishes reserve while the watch is worn.
- Return the crown to the case. Push it fully home and screw it down by hand until it is seated, without cross-threading. The crown must be secured before water exposure.
Calibre 37-02 is specified with a 70-hour ±5% power reserve on the cited Seventies pages. The stated tolerance corresponds to approximately 66.5–73.5 hours, not a promise that every watch will run for exactly 70 hours in every condition. Reserve can vary with winding state, regulation, friction, temperature and service condition.
How do I set the time and stop the seconds hand?
Use the second pull-out position in the general three-position Glashütte Original layout. This position engages the seconds stop, allowing the display to be synchronized with a trusted time signal.
- Release the screw-down crown while the watch is dry.
- Pull the crown to the second operating position (the second click or second pull-out from the case). In the analogous Glashütte Original crown description, this is the time-setting position and the seconds hand stops.
- Turn the hands to the required time. Take account of whether the displayed date is changing as you pass midnight; do not assume the date has advanced until the Panorama Date has completed its change.
- For precise synchronization, wait for the reference time signal, then push the crown back to the winding position so the seconds hand is released.
- Press the crown home and screw it down completely before exposing the watch to water.
If the crown does not give a clear second position or the seconds hand does not stop, do not improvise with the chronograph pushers. Confirm the reference-specific instructions through the manual or an authorised service partner.
Which crown position changes the Panorama Date?
In the general Glashütte Original arrangement, the first pull-out position (position 2) is the date-correction position. The Seventies pages confirm a Panorama Date display, but they do not publish the exact correction direction or the protected hours for each reference.
Recommended Free Tools
Also popular on Amazon
- ELEGANT CARBON FIBER DESIGN: Made of high-quality PU leather with a transparent acrylic window. The smooth PU leather interior reliably protects your mechanical watches from scratches. A stylish eye-catcher and the perfect presentation for your valuable watch collection.
- IMPORTANT SIZE COMPATIBILITY (PLEASE CHECK): To ensure smooth operation and prevent motor damage, this dual watch winder is designed for watches with the following maximum dimensions: Dial diameter under 47 mm, case thickness under 28 mm, and strap circumference under 175-195 mm. It can accommodate large watches, but cannot simultaneously hold two mechanical watches with a dial diameter of 58 mm with crown. Please measure your watch before purchasing.
- OPERATING PRINCIPLE: A watch winder serves exclusively to maintain the power reserve and simulates the natural movement of the wrist. It CANNOT wind a completely stopped watch from zero. Important: Please manually wind the crown of your watch approx 20-40 times before placing it in the winder. It CANNOT start or wind a completely stopped watch from zero. We also recommend manually checking the time once a week.
- INTELLIGENT INTERVAL ROTATION: Programmed with pauses to prevent over-winding. Mode B: 2 min clockwise, 6 min pause, 2 min counterclockwise. Mode L: 2 min counterclockwise, 18 min pause, 2 min clockwise. (If you see the winder rotate and then stop, this is the programmed pause — NOT a malfunction. Please wait through the full pause period (6 min for Mode B, 18 min for Mode L) )You can switch the device off when not in use.(Speed: 970-2430 TPD. Automatic watches only. NOT for Quartz, Seiko Kinetic, or Citizen Eco-Drive).
- CONSTANT POWER SUPPLY (NO BATTERY): Please note that this device does not have a built-in battery and must be permanently connected to a power source (3V~9V, 0.5A) during operation. A connection cable is included (power adapter NOT included). Multiple watch winders can be conveniently connected in series via the cable to save space and power outlets.
- Release the screw-down crown with the watch dry.
- Pull the crown to the first operating position, after the winding position but before the time-setting position.
- Use the direction and date-correction method stated in the manual for the exact reference. Do not infer the direction from another Seventies edition.
- Return the crown to the winding position, then press and screw it down fully.
Because the public product pages do not state a universal date-change lockout period, this article does not prescribe a “safe” clock window. Date mechanisms can be damaged when correction is attempted while their changeover parts are engaged. If your manual does not clearly identify the protected interval, set the date by moving the hands through the hours in the time-setting position or ask an authorised service partner for the reference-specific procedure.
How do I secure the screw-down crown correctly?
After winding or setting, push the crown straight toward the case and begin turning it clockwise by hand so the threads engage cleanly. Continue only until the crown is seated; a crown that stops abruptly, feels gritty or sits proud of the case needs professional attention.
The listed 10-bar water resistance is a model specification, not a guarantee after an impact, ageing seals or an incorrectly seated crown. Never operate the crown or chronograph controls while the watch is wet or submerged. A pressure rating also does not remove the need for seal inspection when the watch has been opened or serviced.
What should I know about the Seventies chronograph pushers?
The cited Seventies references combine a stop-second chronograph with small seconds, 30-minute and 12-hour counters, a power-reserve display and a flyback function. Those features make the controls reference-dependent: button layout, reset behaviour and the exact flyback sequence must be confirmed in the manual for the reference on your case back.
- Do not assume that a pusher sequence from another Seventies edition applies to yours.
- Do not use the chronograph as a substitute for the crown positions; time setting and date correction are performed through the crown.
- Before water exposure, verify that the screw-down crown is fully seated. The product pages identify the crown as screw-down, but they do not turn chronograph operation into a water-use instruction.
- If a pusher sticks, fails to reset or feels abnormal after an impact, stop using the chronograph and arrange authorised service.
Why did my automatic Seventies stop?
The most common explanation is that the watch was unworn long enough to use its available reserve. A Calibre 37-02 Seventies has a stated reserve of 70 hours ±5%, so a watch left still for longer than its remaining reserve can stop without a fault.
- It was unworn: release the crown and manually restart it using the reference-specific winding direction, then secure the crown.
- It stops again soon after winding: note how long it runs and contact an authorised service partner. Repeated short running time can indicate insufficient winding, regulation or a mechanical problem.
- The crown will not release or reseat: stop immediately; forcing a screw-down crown can damage the threads or seals.
- There is condensation, water exposure or impact damage: do not wind or set the watch. Professional inspection is the safer next step.
- The power-reserve display behaves unexpectedly: use the reference manual and service channel rather than treating the display as a universal calibration guide.
Do I need a watch winder?
No. A winder is optional for a Seventies automatic. Normal wear keeps the rotor supplying energy, and manual crown winding is sufficient when the watch has stopped or has been stored.
Also popular on Amazon
- ELEGANT CARBON FIBER DESIGN: Dual Watch Winder with Transparent Acrylic Window to protect your timepiece from scratches while ensuring continuous operation. Its elegant design not only enhances functionality but also serves as a stylish accessory.
- IMPORTANT SIZE COMPATIBILITY (PLEASE CHECK): To ensure smooth operation and prevent motor damage, this dual watch winder is designed for watches with the following maximum dimensions: Dial diameter under 47 mm, case thickness under 28 mm, and strap circumference under 175-195 mm. It can accommodate large watches, but cannot simultaneously hold two mechanical watches with a dial diameter of 58 mm with crown. Please measure your watch before purchasing.
- OPERATING PRINCIPLE: A watch winder serves exclusively to maintain the power reserve and simulates the natural movement of the wrist. It CANNOT wind a completely stopped watch from zero. Important: Please manually wind the crown of your watch approx 20-40 times before placing it in the winder. We also recommend manually checking the time once a week.
- INTELLIGENT INTERVAL ROTATION: Programmed with pauses to prevent over-winding. Mode B: 2 min clockwise, 6 min pause, 2 min counterclockwise. Mode L: 2 min counterclockwise, 18 min pause, 2 min clockwise. You can switch the device off when not in use.(Speed: 970-2430 TPD. Automatic watches only. NOT for Quartz, Seiko Kinetic, or Citizen Eco-Drive).
- CONSTANT POWER SUPPLY (NO BATTERY): Please note that this device does not have a built-in battery and must be permanently connected to a power source (3V~9V, 0.5A) during operation. A connection cable is included (power adapter NOT included). Multiple watch winders can be conveniently connected in series via the cable to save space and power outlets.
A winder can be convenient if you rotate several watches and want one to remain running, but it does not replace correct crown handling or service. Because the cited material does not specify a required winding rate or rotation programme for every Seventies reference, choose settings only from the watch’s manual or an authorised service recommendation. Leaving the watch stopped and restarting it when needed is mechanically acceptable; repeatedly operating a date mechanism without following its protected-hour instructions is not.
What varies between Seventies references?
Use the reference number to resolve differences before applying a procedure. The family can vary in edition, dial treatment, strap or bracelet, and chronograph presentation even when the broad movement description is similar.
Do these 3 things before closing this tab:
1Repair Windows errors before they cause bigger problems2Fix the driver behind crashes, sound loss and screen glitches3Clear out junk files and repair common Windows errors- Calibre and functions: confirm the movement designation and whether the watch has the listed chronograph, flyback and power-reserve displays.
- Crown and date mechanism: verify the position feel, correction direction and date-change safeguards for that reference.
- Case and water specification: check the exact case dimensions and stated water resistance rather than transferring figures from another edition.
- Bracelet or strap fit: cited stainless-steel bracelet versions use a 26 mm end-link width, but end links, clasp geometry and case attachment must match the reference.
- Service history: seals, crown threads and pressure resistance depend on condition and previous work, not only on the original specification.
When should I stop and use authorised service?
Use an authorised Glashütte Original service partner when a crown will not unscrew, will not seat, feels rough, or no longer gives distinct positions. Service is also appropriate after a hard impact, moisture ingress, abnormal chronograph behaviour or a watch that repeatedly loses its reserve shortly after winding.
The public information used here does not establish a single model-specific service interval or pressure-test interval for every Seventies reference. Do not invent one from a different watch. The service portal’s reference search is the appropriate route for technical information and authorised service access.
Independent reader supportYour contribution helps us test, update, and keep practical guides available for everyone.Can I replace the Seventies bracelet or strap?
Possibly, but match the complete interface rather than buying on width alone. Glashütte Original lists a 26 mm end-link width for the cited stainless-steel bracelet versions. Before ordering, verify the exact reference, end-link shape, spring-bar arrangement, clasp and case finish with the manufacturer or an authorised specialist.
How should I use the power-reserve display?
Treat it as an indication of remaining running time, not as a stopwatch for a guaranteed number of hours. The 70-hour ±5% specification applies to the cited Calibre 37-02 Seventies references, while actual reserve depends on the movement’s state and servicing. If the indication and running behaviour disagree consistently, arrange a reference-specific inspection.
Also popular on Amazon
- 【Next Generation LED Crystal Design】ANWBROAD new tech visual LED crystal light-emitting design automatic watch winder, the light penetrates the cup body to form a beautiful light and shadow effect, so that your watch in the light and shadow of the beauty of the mechanical art, exquisite, is the ideal choice for festive greetings
- 【4 Rotation Modes】 The automatic watch winder is very user-friendly and provides 4 modes for users to choose: Mode 1: rotate clockwise for 2 minutes, stop for 6 minutes, recycle; Mode 2: rotate counterclockwise for 2 minutes, stop for 6 Minutes, recycle; Mode 3: Rotate clockwise for 2 minutes, stop for 6 minutes; rotate counterclockwise for 2 minutes, stop for 6 minutes, recycle; Mode 4: clockwise for 5 minutes, rotate counterclockwise for 5 minutes, work for 3 hours and stop 9 hours
- 【Memory Foam Watch Pillow】The watch winder case adopts new upgraded high elasticity memory foam watch pillows, which are soft enough and elastic enough to fit different sizes of watches, and can be used for both men and women's watches. The rotating watch case is an ideal choice for Father's Day, Birthday, Valentine's Day, Anniversary, Christmas, for yourself, your loved one, your parents and more
- 【Dual Power Supply】Can be powered by AC adapter (supplied in the kit) or batteries (not supplied in the kit). Special Note: The automatic watch case winder cannot be powered by both AC power and battery power. When using the AC adapter, remove the batteries
- 【Ultra Quiet Japanese Motor】Our automatic watch winder box is specially designed for automatic watches with a high quality Japanese quiet motor for smooth and quiet operation and precise control. The watch winder is very low, only 5 decibels, which will not affect your office rest, etc
Frequently asked questions
Can I wind the watch while the crown is still screwed down?
No. A screwed-down crown is seated against the case and is not in its operating position. Release the threads first, and never try to turn a resistant crown harder to make it wind.
Is a 10-bar Seventies safe at a depth of 100 metres?
Do not interpret the rating as permission to use the watch at a stated depth or to operate its controls underwater. It is the manufacturer’s water-resistance specification for the model; seal age, impact and crown seating can change real-world protection.
What if my manual and the crown positions seem different?
Follow the manual for the reference engraved on your case back. The three-position arrangement described here is the general Glashütte Original layout, while individual editions can document different mechanisms or operating details.
Where can I obtain reference-specific technical help?
Use Glashütte Original’s service information system with the case-back reference, or contact an authorised Glashütte Original service partner. Provide the full reference and describe any crown, date, chronograph or moisture problem before attempting further operation.
The Tool Desk
Outbyte Driver Updater FREEScan for outdated or missing drivers - takes under a minuteDriver Scan →Outbyte PC Repair FREERepair Windows errors before they cause bigger problemsFix Now →Frequently Asked Questions
Can I wind the watch while the crown is still screwed down?
No. A screwed-down crown is seated against the case and is not in its operating position. Release the threads first, and never try to turn a resistant crown harder to make it wind.
Is a 10-bar Seventies safe at a depth of 100 metres?
Do not interpret the rating as permission to use the watch at a stated depth or to operate its controls underwater. It is the manufacturer’s water-resistance specification for the model; seal age, impact and crown seating can change real-world protection.
What if my manual and the crown positions seem different?
Follow the manual for the reference engraved on your case back. The three-position arrangement is general Glashütte Original guidance, while individual editions can document different mechanisms or operating details.
Where can I obtain reference-specific technical help?
Use Glashütte Original’s service information system with the case-back reference, or contact an authorised Glashütte Original service partner. Provide the full reference and describe any crown, date, chronograph or moisture problem before attempting further operation.
Quick wins for a faster PC:
Repair Windows errors before they cause bigger problemsFix Now →Scan for outdated or missing drivers - takes under a minuteDriver Scan →Quick Recap
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon at the time of purchase will apply.
