Some links on this page are affiliate links: if you buy through them we may earn a commission, at no extra cost to you.
If your Delugs WristPop feels loose, tight or rubs your wrist, stop wearing it and reset the fit rather than forcing the clasp. The WristPop uses an uncut FKM rubber strap: fit it first, count the segments needed on each side, cut along the molded grooves, install the spring bars in the last available holes, then close the deployant clasp and reassess. Leave one extra segment on your first cut because removing rubber is permanent. A slightly loose first fit is expected; remove one segment at a time until the clasp is snug and centered. If it is already pulling, leaving a large clasp gap or causing persistent irritation, do not cut further—contact Delugs about support or replacement parts.
What should I check before changing the WristPop fit?
Take the watch off and inspect the strap, case and clasp before making another cut. The WristPop is designed to be adjusted gradually, and most fit problems come from removing too many segments, trimming the wrong side or closing the deployant unevenly.
As an Amazon Associate I earn from qualifying purchases.
- Confirm that the Royal Pop has clicked fully into the TR90 case frame. It should sit flush without wiggle.
- Check that both spring bars are seated in the intended holes and that the strap is not twisted.
- Look at the clasp gap while the watch is on your wrist. A large gap combined with tension usually means the strap is too short.
- Identify whether the discomfort is looseness, pressure, an off-center clasp or a sharp edge pulling against skin. Each symptom calls for a different correction.
The case-to-watch attachment is reversible: it uses no drilling, glue or permanent modification to the watch. That does not make strap cutting reversible, however; once an FKM segment is removed, it cannot be put back.
How do I loosen a Delugs WristPop that feels too loose?
Remove one segment at a time, alternating checks on your wrist. Delugs notes that “A little loose on the first attempt means you’re on the right track.” The first fit is deliberately conservative so you can shorten the strap without risking an over-tight result.
Popular on Amazon
- Ergonomic Handle Design – Features a specially designed handle that offers a comfortable, secure grip, allowing for better control and effortless during repeated use.
- Essential Tool for Watch Repair Professionals – A practical and reliable solution tailored for watchmakers and repair technicians, streamlining strap adjustments and maintenance tasks.
- High-Strength Steel Construction – Made from durable steel with high hardness for excellent wear resistance—ensures long-term sturdiness and consistent performance even under heavy use.
- Precision Watch Strap Hole Punch – Specifically engineered to accurately create clean holes in watch straps and excess material with ease, ensuring a fit and professional finish.
- Compact Lightweight Build – Its small, portable design makes it easy to carry in your toolkit, while the efficient mechanism reduces hand fatigue—making repairs faster and more convenient.
Before trimming, have watch strap cutting scissors with a sharp, controllable tip. Ordinary blunt scissors can crush the rubber and make it harder to follow the molded groove cleanly.
- Fit the uncut strap. Put the watch and strap on your wrist in the position where you normally wear them. Bring the two ends together without stretching the FKM rubber.
- Count the segments. Note how many molded segments are needed on each side for the clasp to close. Count separately; your wrist may need different lengths on the two sides.
- Mark a cautious first cut. Leave one additional segment beyond your estimate. This extra segment is your margin if the first try is tighter than expected.
- Cut on the groove. Make a straight cut along the molded line, keeping the scissors square to the strap. Do not remove several segments at once.
- Reinstall the hardware. Put the spring bars in the last available holes, close the leaf-spring deployant and check that the clasp sits over the underside of your wrist rather than pulling to one side.
- Reassess while moving. Flex your wrist, rotate the watch and make sure the clasp stays closed without pressure or a dangling gap. If it remains loose, remove exactly one more segment and repeat the check.
Stop shortening when the case stays in place during normal movement and the clasp closes with gentle pressure. A rubber strap should not need to be stretched to keep the watch from sliding.
Free tools Windows power users keep installed
One-click scans. No signup required.
What should I do if my WristPop feels too tight?
Do not keep cutting. Pulling at the wrist, pressure from the clasp, numbness or an excessive gap at the clasp are signs that too many segments may have been removed or that the strap is being tensioned incorrectly.
Check the fit without forcing the clasp
Open the deployant, let the strap relax and refit the watch in its normal position. If the strap only feels tight when the clasp is being closed, confirm that the ends are lying flat and that the spring bars are in the last available holes. Never force the clasp over a strap that is visibly under tension.
Know when the cut is the problem
If the strap remains tight after you verify the hardware, the current guide treats this as an overly tight failure mode. Further trimming will worsen it. Contact Delugs to ask about replacement wearing parts or a support solution, and describe how many segments were removed from each side.
Also popular on Amazon
- 1. Made of high quality material, durable.
- 2. The adjustable knob can adjust the width of the container arbitrarily.
- 3. Stainless steel double-sided screws, fixed by rubber cushions.
- 4.It is a rod forming dyeing system.
- 5. 8RPM constant speed rotation.
Because cutting is permanent, keep the removed pieces and take clear photos of the strap, clasp position and case connection. Those details can help support determine which replacement component matches your WristPop reference.
Do these 3 things before closing this tab:
1Scan for outdated or missing drivers - takes under a minute2Clear out junk files and repair common Windows errors3Fix the driver behind crashes, sound loss and screen glitchesWhy is my WristPop rubbing my wrist?
Delugs does not publish a separate WristPop diagnosis for skin rubbing. The practical first checks are fit-related: excessive tension, a skewed clasp or an edge being pulled against the wrist. These checks follow the manufacturer’s fitting instructions rather than a clinical skin assessment.
Inspect the pressure points
- Look for a clasp that is rotated toward one side. An off-center clasp can press repeatedly on the same spot.
- Check whether the strap edge is folded, twisted or stretched against the wrist instead of lying flat.
- Compare the tightness with the clasp open. If pressure disappears immediately, the strap may be too short.
- Check the case frame for movement. A Royal Pop that is not flush in the TR90 frame can change how the watch bears on your wrist.
Refit conservatively
Open the clasp, reposition the watch and make sure both sides are aligned before changing any length. If the clasp is off-center, trim the opposite side one segment at a time rather than cutting the already-short side. If irritation persists, remove the watch and contact Delugs; do not continue wearing it through pain, redness or broken skin.
How do I center the WristPop clasp?
Do not assume both sides must be the same length. Delugs states, “Wrists aren’t symmetrical; uneven cuts are completely normal.” The clasp should be centered on your wrist, not necessarily matched segment-for-segment.
- Close the clasp gently and identify which direction it is displaced.
- Open the clasp and determine which side needs to become shorter to move the clasp toward the center.
- Remove one segment from that side only, cutting on the next molded groove.
- Reinstall the spring bars, close the clasp and check the position with your wrist relaxed.
- Repeat in single-segment increments until the clasp is centered without creating pressure.
If centering requires removing another segment and the result becomes tight, stop and ask Delugs about replacement parts rather than sacrificing comfort for symmetry.
The Tool Desk
Outbyte Driver Updater FREEScan for outdated or missing drivers - takes under a minuteDriver Scan →Outbyte PC Repair FREEClear out junk files and repair common Windows errorsFree Scan →Also popular on Amazon
- [PRECISION HOLE PUNCHING] These watch bracelet cutting pliers are expertly engineered to punch clean, round holes into watch straps of all sizes without causing any damage or fraying. The cutting mechanism ensures smooth edges every time, making it perfect for leather, rubber, and metal bands. Achieve professional results at home or in your workshop with this essential watchmaker tool.
- [DURABLE STAINLESS STEEL CONSTRUCTION] Crafted from premium stainless steel, these watch band cutting pliers offer exceptional strength and long lasting stability. The robust material resists rust and , ensuring reliable performance through countless repairs. This sturdy build makes them an indispensable tool for both professional watchmakers and DIY enthusiasts who demand durability and precision.
- [ERGONOMIC DESIGN FOR COMFORT] Featuring ergonomically shaped handles with a soft grip, these bracelet cutting pliers reduce hand fatigue during extended use. The integrated high elasticity return spring allows for effortless repeated action, minimizing strain on your hands and wrists. Work longer and more comfortably on intricate watch repairs without losing control or accuracy.
- [VERSATILE MATERIAL COMPATIBILITY] Designed to work flawlessly with a wide range of strap materials, including leather, silicone, nylon, and metal watch bands. The precision punch creates smooth edges that prevent tearing or cracking, preserving the integrity of your straps. Whether you are resizing a new band or customizing an old one, these pliers deliver consistent results across all material types.
- [MULTIFUNCTIONAL WATCH REPAIR TOOL] Beyond cutting and punching, these pliers excel at the precise removal and installation of spring bar pins on all types of watches, bands, and links. This multifunctional capability streamlines your repair process, saving time and effort. Ideal for watchmakers, technicians, and hobbyists, this tool enhances efficiency for a wide variety of watch maintenance tasks.
How do the WristPop clasp and case attachment work?
Leaf-spring deployant clasp
The clasp is a leaf-spring deployant. To open it, pinch one side closed, then the other, and pull upward on either side. Close it slowly the first time so skin is not caught between the spring-loaded sections. A proper closure is deliberate and secure; it should not require you to slam or force the clasp.
Royal Pop connection
The Royal Pop should click into the TR90 case frame and remain flush without wiggle. If it rocks or sits proud of the frame, remove the watch and reseat the attachment before evaluating strap length. The connection is reversible and does not require drilling, adhesive or a permanent change to the watch.
Can I recut the WristPop strap?
Yes, the strap is intended to be cut to size, but every cut is irreversible. The safe sequence is test, cut and check: wear the uncut strap, count the required segments, leave one extra segment on the first attempt, cut along the grooves, install the spring bars and reassess.
Do not cut based only on a ruler measurement. Wrist position, clasp placement and the amount of natural slack all affect the result. The same number of segments on each side is not required, and matching lengths can leave the clasp off-center.
Can I return a WristPop after cutting it?
Delugs’ WristPop page says its support team handles returns and exchanges and that wearing parts are available individually. Its general Rubber CTS policy accepts only uncut straps for returns, so confirm WristPop-specific eligibility with Delugs before cutting or requesting a return.
Also popular on Amazon
- PRECISE PUNCHING: The watch bracelet cutting pliers are specially designed to accurately punch round holes into straps without causing any damage, suitable for various sizes.
- ROBUST METAL: Made from excellent quality stainless steel, these watch band cutting pliers are sturdy and stable, making them an ideal tool for watchmakers and repair technicians.
- ERGONOMIC DESIGN: Featuring ergonomically designed handles, the bracelet cutting pliers provide a comfortable grip and include a high elasticity return spring to minimize operator fatigue.
- SMOOTH EDGES: The watch band puncher ensures precise punching with smooth edges, guaranteeing that the straps remain undamaged and are compatible with various materials.
- VERSATILE USE: Designed for all types of watches, bands, and links, these pliers allow for accurate removal and installation of spring bar pins, enhancing overall efficiency for watch repairs.
If you are still deciding on size, keep the strap uncut, test the watch over clothing only if that reflects how you will actually wear it, and contact support with your wrist measurement and Royal Pop reference. Once trimmed, treat the strap as a fitted component rather than a returnable standard-length item unless Delugs confirms otherwise.
What WristPop versions and sizing limits should I know?
WristPop fit advice applies across the current Royal Pop range, but the case design must match the watch reference and crown position. Delugs lists eight supported Royal Pop references, with separate case designs for Lépine and Savonnette crown positions.
| Current product detail | Published figure or qualification |
|---|---|
| Case options | 17 options, according to Delugs’ 2026 product information |
| Strap colours | 14 colours, according to Delugs’ 2026 product information |
| Possible combinations | 238 case-and-strap combinations, according to Delugs’ 2026 product information |
| Designed wrist size | Down to a 13.5 cm wrist; comfort still depends on case, clasp position and individual anatomy |
| Standard price | US$185 after the promotional period, as listed for 2026 |
| Shipment timing | The 2026 product page says shipments begin at the end of October 2026 |
These figures describe the current 2026 listing and may change. Select the correct case design before trimming; a strap that fits one crown-position reference is not evidence that another reference uses the same case geometry.
Crashes, No Sound, or Screen Glitches?
Random freezes, missing sound and display glitches usually trace back to one bad driver. Find and replace yours safely.Free scan · under a minuteWindows Errors? Fix Them Before They Spread
Repair common Windows errors and clear accumulated junk for a smoother, more stable PC - no reinstall needed.Free scan · no reinstallWould a fixed-length strap be easier than WristPop?
A fixed-length strap avoids cutting, while WristPop trades that convenience for adjustable sizing and a reversible case installation. Choose based on how much you value a centered clasp, replacement flexibility and the ability to fine-tune the fit.
| Consideration | WristPop cut-to-size system | Fixed-length strap |
|---|---|---|
| Initial setup | Requires a test-fit, careful cutting and a final check | Usually ready to wear if the purchased length is correct |
| Fine adjustment | Segments can be removed one at a time, with unequal cuts allowed | Limited to existing holes or buckle positions |
| Over-shortening risk | High once rubber is cut; leave an extra segment first | No cutting error, but an unsuitable length may remain uncomfortable |
| Clasp centering | Can be tuned by trimming one side independently | Depends on the strap’s manufactured proportions |
| Installation | Royal Pop attachment is reversible and uses no glue or drilling | Depends on the strap and watch hardware |
| Replacement support | Delugs says wearing parts are available individually; confirm compatibility | Replacement policy varies by manufacturer |
What is the fastest way to diagnose the problem?
- Loose but comfortable: remove one segment, then reassess on the wrist.
- Tight, pulling or leaving a large clasp gap: stop cutting and contact Delugs.
- Clasp off-center: shorten the opposite side one segment at a time; equal cuts are not required.
- Rubbing at one point: inspect strap tension, clasp alignment and case seating; remove the watch if irritation continues.
- Case movement: reseat the Royal Pop in the TR90 frame and verify a flush, wiggle-free connection before wearing it.
Keep a record of how many segments remain on each side. That simple note makes future troubleshooting and any replacement-parts request more precise.
Also popular on Amazon
- Customizable Fit: The cuttable design allows the strap to be trimmed to the perfect length, ensuring a comfortable and secure fit for any wrist size (We recommend cutting a section at a time so as not to cut too much off the strap)
- Fast-Release Strap: Equipped with a fast release system, the strap can be easily attached and detached from the watch case without the need for any tools. It is available in multiple sizes:18 mm/19 mm/20 mm/21 mm/22 mm
- Water & Sweat Resistance: This band is highly water and sweat resistant, making it ideal for an active lifestyle, perfect for swimming, diving or other sports. Best of all, it doesn't attract dust
- Durable Material: The soft strap is made of premium fluororubber, which is highly wear-resistant and high-temperature resistant, making it suitable for daily use and harsh conditions
- Adjustable to fit Wrist Size: Fits wrist sizes 5.5”-10”. Total strap length can be adjusted to a maximum of 204mm and a minimum of 94mm (excluding buckle length), rubber can be cut to a maximum of 55mm on each side for optimal fit. It can also be fine-tuned via the milled clasp
When should I contact Delugs instead of adjusting it again?
Contact Delugs when the strap is too short, the clasp cannot close without force, the case will not sit flush, or skin irritation continues after a conservative refit. Include your Royal Pop reference, crown-position design, remaining segment count on each side and photographs of the clasp and case connection.
Support can also clarify whether your trimmed WristPop qualifies for a return or exchange and which wearing parts are available individually. Do not assume the general uncut-strap Rubber CTS return rule automatically determines WristPop eligibility; ask before sending anything back.
Quick wins for a faster PC:
Scan for outdated or missing drivers - takes under a minuteDriver Scan →Repair Windows errors before they cause bigger problemsFix Now →Fix the driver behind crashes, sound loss and screen glitchesFind Drivers →Frequently Asked Questions
How small a wrist is the WristPop designed to fit?
Delugs lists the case frame as designed to fit wrists down to 13.5 cm. Measure the wrist where you will wear the watch and allow for the clasp and case position, because the minimum published wrist size is not a guarantee of identical comfort for every wearer.
Are Lépine and Savonnette Royal Pop cases interchangeable?
No assumption of interchangeability is safe. Delugs supports eight Royal Pop references and uses separate case designs for Lépine and Savonnette crown positions, so verify the exact reference before installing or trimming a strap.
What should I do with the segments I cut off?
Keep every removed piece in a labeled bag with the watch reference and the date of the adjustment. The pieces document how much was removed and can help Delugs identify a compatible replacement component if the final fit is too tight.
Is it safe to keep wearing the watch while my skin is irritated?
No. Remove the watch when rubbing causes persistent redness, pain or broken skin, and contact Delugs after checking the strap and clasp alignment. Resume wearing it only after the source of the pressure has been corrected and your skin has recovered.
Recommended Free Tools




